Note to Online ReaderThis manual has been altered from the original toprotect Xantrex's intellectual property.The replacement parts lists and sch
OPERATING MANUAL FEATURES AND SPECIFICATIONSRelease 1.0 (98/07) 1-11. FEATURES AND SPECIFICATIONS1.1 DescriptionThis series of power supplies provide
FEATURES AND SPECIFICATIONS OPERATING MANUAL1-2 Release 1.0 (98/07)1.3 Specifications1.3.1 Electrical SpecificationsThese specifications are warrante
OPERATING MANUAL FEATURES AND SPECIFICATIONSRelease 1.0 (98/07) 1-31.3.1 Electrical Specifications (continued)Table 1.3-2 Specifications for 100V to 6
FEATURES AND SPECIFICATIONS OPERATING MANUAL1-4 Release 1.0 (98/07)1.3.2 Additional SpecificationsRise Time (No Load, Full Load): 1 7.5V to 60V model
OPERATING MANUAL FEATURES AND SPECIFICATIONSRelease 1.0 (98/07) 1-51.3.5 Remote Programming and MonitoringRemote Analog Programming (Full Scale Input
FEATURES AND SPECIFICATIONS OPERATING MANUAL1-6 Release 1.0 (98/07)1.3.7 Mechanical Specification (continued)Figure 1.3-2 Dimensional Drawings(Dimensi
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-12. INSTALLATION2.1 IntroductionThis section provides recommendations and procedures for inspecting
INSTALLATION OPERATING MANUAL2-2 Release 1.0 (98/07)2.3.1 Initial Inspection (continued)Figure 2.3-1 Power Supply Front PanelOVP Adjust Potentiometer
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-32.3.1 Initial Inspection (continued)Figure 2.3-2 Power Supply Rear Panel(Bus bar output model (7.5
INSTALLATION OPERATING MANUAL2-4 Release 1.0 (98/07)2.3.2 Periodic CleaningNo routine servicing of the power supply is required except for periodic c
OPERATINGMANUALTM-F2OP-01XNOperatingManual forXFR SERIESPower SupplyThis manual covers2800 Watt models:7.5-300 100-2812-220 150-1820-130 300-940-70 60
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-52.4 Location, Mounting, and VentilationUse the power supply in rack mounted or in benchtop applic
INSTALLATION OPERATING MANUAL2-6 Release 1.0 (98/07)2.5 AC Input Power WARNINGThere is a potential shock hazard if the power supply chassis and cover
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-72.5.3 AC Input Wire Connection1. Strip outside insulation 4" (10 cm). Strip 0.55" (14 m
INSTALLATION OPERATING MANUAL2-8 Release 1.0 (98/07)2.6 Functional TestsThese functional test procedures include power-on and front panel function che
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-92.6.4 Current Mode Operation Check1. Ensure the front panel AC power switch is set to OFF.2. Turn
INSTALLATION OPERATING MANUAL2-10 Release 1.0 (98/07)2.7 Load ConnectionThis section provides recommendations for load wires and how to connect them f
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-112.7.1 Load Wiring (continued)Figure 2.7-1 Maximum Load Wire Length for 1V Line DropNoise and Impe
INSTALLATION OPERATING MANUAL2-12 Release 1.0 (98/07)2.7.2 Making Load Connections (continued)7.5V to 100V ModelsThe 7.5V to 100V models come with a b
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-132.7.2 Making Load Connections (continued)To make load connections to a 7.5V, 300A power supply:1.
INSTALLATION OPERATING MANUAL2-14 Release 1.0 (98/07)2.7.2 Making Load Connections (continued)150V to 600V ModelsWARNINGTo protect personnel against a
PRINTED IN CANADAWARRANTYThis unit is guaranteed for five (5) years from the date of delivery against defects in material and workmanship.This does no
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-152.7.4 Connecting Single LoadsFigure 2.7-5 and Figure 2.7-6 show recommended load and sensing con
INSTALLATION OPERATING MANUAL2-16 Release 1.0 (98/07)2.7.5 Connecting Multiple Loads (continued)Radial Power Distribution MethodTo connect distributed
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-172.8 Local and Remote SensingUse connections at the rear panel J10 sense connector to configure t
INSTALLATION OPERATING MANUAL2-18 Release 1.0 (98/07)2.8.3 Using Remote Sensing WARNINGThere is a potential shock hazard at the sense points when usi
OPERATING MANUAL INSTALLATIONRelease 1.0 (98/07) 2-192.8.3 Using Remote Sensing (continued)Figure 2.8-2 Connecting Remote Sense Lines
OPERATING MANUAL LOCAL OPERATIONRelease 1.0 (98/07) 3-13. LOCAL OPERATION3.1 IntroductionOnce you have installed the power supply and have connected b
LOCAL OPERATION OPERATING MANUAL3-2 Release 1.0 (98/07)3.2.1 Operating Modes and Automatic Crossover (continued)Constant Voltage Mode OperationThe pow
OPERATING MANUAL LOCAL OPERATIONRelease 1.0 (98/07) 3-33.2.3 Setting Output Voltage and Current LimitInstall the power supply and connect the load as
LOCAL OPERATION OPERATING MANUAL3-4 Release 1.0 (98/07)3.3 Using Over Voltage Protection (OVP)The OVP circuit protects the load in the event of a rem
OPERATING MANUAL LOCAL OPERATIONRelease 1.0 (98/07) 3-53.4 Using the Shutdown FunctionUse the Shutdown function to disable or enable the supply'
OPERATING MANUAL ABOUT THIS MANUALRelease 1.0 (98/07) iABOUT THIS MANUALThis OPERATING MANUAL contains user information for the XFR Series of variable
LOCAL OPERATION OPERATING MANUAL3-6 Release 1.0 (98/07)3.5 Using Multiple SuppliesCAUTIONDo not connect power supplies from different manufacturers i
OPERATING MANUAL LOCAL OPERATIONRelease 1.0 (98/07) 3-73.5.2 Configuring Multiple Supplies for Parallel OperationUse parallel operation to obtain a h
LOCAL OPERATION OPERATING MANUAL3-8 Release 1.0 (98/07)3.5.3 Configuring Multiple Supplies for Split Supply OperationSplit supply operation uses two
OPERATING MANUAL LOCAL OPERATIONRelease 1.0 (98/07) 3-93.5.3 Configuring Multiple Supplies for Split Supply Operation (continued)Positive-negative Sup
LOCAL OPERATION OPERATING MANUAL3-10 Release 1.0 (98/07)3.7 User DiagnosticsIf your power supply is not performing as described in this operating man
OPERATING MANUAL LOCAL OPERATIONRelease 1.0 (98/07) 3-113.7.3 Troubleshooting for OperatorsUse the checks in Table 3.7-1 to ensure that the power sup
OPERATING MANUAL REMOTE OPERATIONRelease 1.0 (98/07) 4-14. REMOTE OPERATION4.1 IntroductionThe rear panel switches and connector on the power supply a
REMOTE OPERATION OPERATING MANUAL4-2 Release 1.0 (98/07)4.2.1 Rear Panel SW1 Switch (continued)The rear panel SW1 switch is marked with the word OPEN
OPERATING MANUAL REMOTE OPERATIONRelease 1.0 (98/07) 4-34.2.3 Rear Panel J2 Connector (continued)See Table 4.2-2 for the list of the J2 connector term
REMOTE OPERATION OPERATING MANUAL4-4 Release 1.0 (98/07)4.3 Remote Analog Programming of Output Voltage and CurrentLimitRemote analog programming all
MANUAL CHANGES OPERATING MANUALii Release 1.0 (98/07)MANUAL CHANGESThere are no changes at this time.
OPERATING MANUAL REMOTE OPERATIONRelease 1.0 (98/07) 4-54.3.2 Remote Analog Programming Procedure (continued)Notes:1. The rear panel SW1 switch is mar
REMOTE OPERATION OPERATING MANUAL4-6 Release 1.0 (98/07)4.3.2 Remote Analog Programming Procedure (continued)Figure 4.3-1 Connecting Programming Sourc
OPERATING MANUAL REMOTE OPERATIONRelease 1.0 (98/07) 4-74.5 Using the Isolated (ISOL) Programming Interface OptionThe 4-channel Isolated (ISOL) Progr
OPERATING MANUAL CALIBRATIONRelease 1.0 (98/07) 5-15. CALIBRATION5.1 Introduction HIGH ENERGY/HIGH VOLTAGE WARNINGSExercise caution when using and ser
CALIBRATION OPERATING MANUAL5-2 Release 1.0 (98/07)5.2 Calibration Setup5.2.3 Accessing Calibration PotentiometersWARNINGDisconnect AC power from the
OPERATING MANUAL CALIBRATIONRelease 1.0 (98/07) 5-35.3 Calibrating for Programming AccuracyThe factory calibrates the offset and range of the voltage
CALIBRATION OPERATING MANUAL5-4 Release 1.0 (98/07)5.4 Calibrating for Readback AccuracyThe factory calibrates the offset and range of the output vol
Xantrex Technology Inc.8587 Baxter PlaceBurnaby, B.C.Canada V5A 4V7Tel: 604-415-4600Fax: 604-415-4674Toll Free North America1-800-667-8422e-mail: xant
OPERATING MANUAL CONTENTSRelease 1.0 (98/07) iiiCONTENTSAbout This Manual ...
CONTENTS OPERATING MANUALiv Release 1.0 (98/07)3. LOCAL OPERATION3.1 Introduction...
OPERATING MANUAL ILLUSTRATIONS AND TABLESRelease 1.0 (98/07) vLIST OF ILLUSTRATIONSFigure 1.3-1 Typical Input Current Characteristics...
Kommentare zu diesen Handbüchern